![]() Dominator plats and gskill are the way to go. Its been nothing but trouble for this board. If your ram is Vengeance series from corsair get rid of it. Final step is to take it to a shop for troubleshooting. Try different video cable and video inputs on monitor. Turn monitor power on and then hit the power button, give the mobo 5-7 minutes, you should notice gpu and cpu fans spinning up if not try a different psu. Ensure power cable is fully plugged into monitor and power strip/wall outlet, hook up and ensure psu power cable is hooked up fully to psu and in wall or powrr strip. ensure monitor cable is hooked up to your monitor fully and set to correct video input. Hook up the keyboard and mouse using the usb ports closest to the ps2 port. Theres no signal to the monitor, either from the GPU or the iGPU. Ensure atx, eps 12v (at top of mobo towards rear) hooked to mobo, then pcie power is hooked up to gpu properly. Of the status LEDs on the motherboard, the DRAM LED is lit green, the CPU LED is lit red, and the GPU/Boot Device LEDs are off. clear the cmos using the jumper (read your manual), put jumper back in its spot, apply tim to the cpu and reattach heatsink to cpu mount bracket and fan to cpu header. Disconnect power totally, ensure ram is in slots 2 and 4 from left to right, ensure to shove gpu into pcie x16_1 fully seated, hook up a monitor closest to the screw side if the pci bracket. Since the socket lays on 1 side and the latch bar is closer to the pcie socket, the tip of the latch bar faces left, ensure when you insert the cpu the letters are closer to the ram and not up and down on the mobo. You can read my Guide: How to find a good PSU.Ensure mobo is placed on the box it came with ,psu,gpu, out of case completely, Take the heatsink off, take cpu out of socket, ensure you dont have any bent pins on the cpu. So i would test with a different, either known good and not too old, or new PSU. This had 5 years of warranty, and if it's now 8 years old or so, it might already cause weird problems. The 5VSB circuit thankfully uses a Chemi-Con cap."). The electrolytic capacitors slowly lose their properties with age, and they didn't use very good capacitor brands/models on the secondary side where it counts, see here ("The filtering caps in the secondary side are provided by Teapo and CapXon, definitely not the best choices for a PSU of this price range, but we have seen worse. This is the original RM650 from circa 2013? Now, that wasn't a bad model, but if it's anywhere near that old, it might not be adequate anymore. Make sure the 8-pin EPS plug is fully latched in on the CPU_PWR header next to the CPU. ![]() ![]() Try with only one RAM module in slot A2 (2nd from left). It will be spread by the cooler pressure.įor all further testing, take out the graphics card and use the iGPU. I use soft, lint-free paper towels and q-tips dipped in high-purity isopropanol alcohol to clean, and then apply a drop of new heatpaste onto the middle of the CPU, at least the size of a large grain of rice. So i'd then clean it 100% and then apply new heatpaste. Finally, how to do it properly once it all works: Clean the CPU heatspreader and the cooler base, because when you re-use old heatpaste, there can be trapped air bubbles which could lead to overheating. For further testing, you can put the cooler back on without replacing the heatpaste. Read here for example, it's more common than people think.Īnyway, if the pins are all perfectly aligned, you can put the CPU back in. If different kits of RAM are not working at all, it could be that you accidentally bent some pins during CPU installation. A lot of the pins on the right side of the socket go straight to the memory slots, since the CPU houses the memory controller (IMC). If the pads under the CPU and some pins of the socket don't make proper contact, you can have all kinds of problems. ![]() Check very carefully (with a magnifying glass, if possible) if all the pins look exactly the same, in position and in height. Take out the CPU and carefully inspect the underside and the socket for any bent pins, foreign objects, dirt, or other abnormalities. So I tried my friends Athlon X2 CPU, but it still wouldn't boot and the CPU led was still. I assumed the CPU had died, since I OC'ed it when it was already factory OC'd. The CPU led on the mobo was lighting red. Normally i would suggest to update the BIOS using the Flash BIOS Button, but none of the ♚TX (micro-ATX) B660 boards have that feature. I tried to reset by the reset button, but it didn't work, so I turned off the Power Supply and back on. ![]()
0 Comments
Leave a Reply. |
Details
AuthorWrite something about yourself. No need to be fancy, just an overview. ArchivesCategories |